Amana RSKP0006 Manuel d'instructions télécharger pdf

Description

Control board installation procedures are described in detail

in these instructions. Read and follow these instructions

carefully before replacing the control board. Failure to do so

may result in control board damage.

Important Note:

Damage to the control board can occur from failure to

disconnect power supply or failure to set the master switch

(located on the control board) to OFF before removing the

low voltage terminal strip cover from an installed control

board. Damage to this board by not following these instruc-

tions is considered misuse and not covered under either the

standard unit warranty or any extended service contract.

Important Note:

All warranty replaced boards must be returned to the parts

source from which they were purchased to insure proper

warranty credit.

PTAC CONTROL BOARD KIT

RSKP0006

NSTALLATION

NSTRUCTIONS

IO-660A

November 2006

ATTENTION INSTALLING PERSONNEL

As a professional installer you have an obligation to know the product better than the customer. This

includes all safety precautions and related items.

Prior to actual installation, thoroughly familiarize yourself with this Instruction Manual. Pay special attention

to all safety warnings. Often during installation or repair it is possible to place yourself in a position which is

more hazardous than when the unit is in operation.

Remember, it is your responsibility to install the product safely and to know it well enough to be able to

instruct a customer in its safe use.

Safety is a matter of common sense...a matter of thinking before acting. Most dealers have a list of specific

good safety practices...follow them.

The precautions listed in this Installation Manual are intended as supplemental to existing practices.

However, if there is a direct conflict between existing practices and the content of this manual, the

precautions listed here take precedence.

RECOGNIZE THIS SYMBOL AS A SAFETY PRECAUTION.

Figure 1

Electrostatic Discharge (ESD) Precautions

Before removing the new control board from the static wrap,

it is very important to discharge any static electricity. This

can be accomplished in two methods. Servicer can wear a

ground strap or by touching the metal chassis before replac-

ing the board.

Existing Control Board Removal Procedures

1. Disconnect power to the unit by unplugging the power

cord at the wall outlet or subbase, or disconnect power at

the fuse box or circuit breaker.

2. If the cabinet front is screwed to the chassis, remove the

1/4” screw (or screws) located behind the inlet grille. Pull

the inlet grille forward from the top of the grille to access

screw(s).

FRONT MOUNTING

HOLE

Printed in USA

1 2 3 4 5 6 ... 11 12

Résumé du contenu

Page 1 - RSKP0006

DescriptionControl board installation procedures are described in detailin these instructions. Read and follow these instructionscarefully before repl

Page 2 - TRANSFORMER

10WIRING DIAGRAMS2 RIBBED WIRE MUST BE CONNECTED AS SHOWN.NOTES1 WARNING: DISCONNECT POWER BEFORE SERVICING. WIRING TO UNIT MUST BE PROPERLY P

Page 3 - Figure 6

11THIS PAGE LEFT INTENTIONALLY BLANK

Page 4 - INDOOR COIL THERMISTOR - RED

12Goodman Company, L.P.2550 North Loop West, Suite 400Houston, TX 77092Quality Makes the Difference!All of our systems are designed and manufactured

Page 5

23. Remove cabinet front from chassis by tilting the bottom ofthe front forward, lifting slightly up and forward.4. If a remote thermostat or any low

Page 6 - Remote Thermostat

3A3. Replace the heater panel, routing the yellow wirearound the right end of the heater panel and into thecontrol panel pulling snug to prevent the w

Page 7 - Figure 10

4C. If the existing Indoor Coil Thermistor (with the REDwires) was connected to the board by a plug-onconnector, reconnect it to the new board on the

Page 8 - WIRING DIAGRAMS

519. Power Vent/Power Door Units Only(See Wiring Diagram Page 9)Reconnect the wires across the top terminals of thecontrol board. Connect as follows:

Page 9

6BLACK w/WHITE STRIPEYELLOW w/BLACK STRIPEREDGREENWHITEYELLOWBLUEGREEN w/YELLOW STRIPERemote ThermostatBROWN*Only load wires needed for accessories at

Page 10 - HIGH VOLTAGE!

7REV.VALVEFANLOWFANHIGHLINE 1ON24VAC-TRANSFORMERDSI IN GLGHBYELLOWHeat Pump models ONLY.Must not be usedon PTC models.RIBBON CONNECTORLeft is ONPositi

Page 11

8WIRING DIAGRAMS TO UNIT MUST BE PROPERLY POLARIZED (FOR 5V) AND GROUNDED.R TO:G, W2(FACTORY OR FIELD) COOL UNITG, Y/W14 ON UNITS WITH FRONT DESK

Page 12 - Quality Makes the Difference!

9WIRING DIAGRAMS2 RIBBED WIRE MUST BE CONNECTED AS SHOWN.NOTES:1 WARNING: DISCONNECT POWER BEFORE SERVICING. WIRING TO UNIT MUST BE PROPERLY P

Commentaires sur ces manuels

Pas de commentaire

Amana RSKP0006 Manuel d'instructions

Naviguer en ligne ou télécharger Manuel d'instructions pour Thermostats Amana RSKP0006. Amana RSKP0006 Instruction manual [en] Manuel d'utilisatio

Résumé du contenu

Commentaires sur ces manuels

Produits connexes et manuels pour Thermostats Amana RSKP0006