Amana PTC153E25AXXXAA Manuel d'instructions télécharger pdf

PTAC

WIRELESS KITS (DT01*, DS01*, DD01*)

I

NSTALLATION INSTRUCTIONS

November 2007

IO-644D

The following installation instructions are for a typical installation.

Please contact your PTAC salesperson

for additional assistance and explanation prior to ordering materials or cutting openings.

USE ONLY ONE DD01* PASSIVE INFRARED MOTION SENSOR (PIR) DOOR SWITCH

COMBINATION DEVICE AND/OR ONE DS01* TO ONE DIGISMART PTAC UNIT.

DS01*

DD01*

DT01*

AIR CONDITIONING SENSOR

®

is a trademark of Maytag Corporation and is used

under license to Goodman Company, L.P. All rights reserved.

ATTENTION INSTALLING PERSONNEL

As a professional installer you have an obligation to know the product better than the customer.

This includes all safety precautions and related items.

Prior to actual installation, thoroughly familiarize yourself with this Instruction Manual.

Pay special attention to all safety warnings. Often during installation or repair

it is possible to place yourself in a position which is more hazardous than when the unit is in operation.

Remember, it is your responsibility to install the product safely and to know it well enough

to be able to instruct a customer in its safe use.

Safety is a matter of common sense...a matter of thinking before acting.

Most dealers have a list of specific good safety practices...follow them.

The precautions listed in this Installation Manual are intended as supplemental to existing practices.

However, if there is a direct conflict between existing practices and the content of this manual,

the precautions listed here take precedence.

IO-644C~IO-644C~092007~4

1 2 3 4 5 6 ... 11 12

Résumé du contenu

Page 1 - INSTRUCTIONS

PTACWIRELESS KITS (DT01*, DS01*, DD01*)INSTALLATION INSTRUCTIONSNovember 2007IO-644DThe following installation instructions are for a typical installa

Page 2 - Preparation

10PTACMOTIONSENSOROUTSIDEPTACMOTIONSENSOROUTSIDETypical Room LayoutsNOTE: This equipment has been tested and found to comply with thelimits for a Clas

Page 3 - DD01* Kit

11THIS PAGE INTENTIONALLY LEFT BLANK

Page 4 - Door Magnet Installation

12Goodman Company, L.P.5151 San Felipe, Suite 500 • Houston, TX 77056www.amana-ptac.com© 2005 - 2007 Goodman Company, L.P.Due to policy of continued

Page 5 - ON BOTTOM OF DD01*

2Antenna Installation For DT01* KitA DT01* antenna must be installed to the PTAC to allowoperation of either the DS01* remote RF thermostat or aDD01*

Page 6 - Binding of RF Devices

3.2. Remove thermostat from mounting plate by pulling apart.3. Place thermostat mounting plate against the wall at de-sired location and mark placemen

Page 7 - Configuration Settings

4Door Magnet InstallationMount the door magnet holder on the front of the door where it will be as close as possible to the bottom of the motionsensor

Page 8 - Setback Temps - DD01*

5Select one of the three slots that places the magnet ½” from the sensor mounting plate on the door frame. See expamplesbelow. The door frame and door

Page 9

62. Press and then immediately release the white tactilebutton on the back of the DS01* thermostat. shouldnow be displayed on the PTAC LED display

Page 10 - Typical Room Layouts

7Configuration SettingsThe PTAC control will automatically self-configure to work with the wall thermostat (DS01* Kit) if installed. The PTACcontrol

Page 11

8Setback Temps - DD01*The DD01* and the DigiSmart control can be programmed for 3 different times to activate temperature setbacks. Thecurrent factory

Page 12 - • Houston, TX 77056

97. Press HEAT key to scroll to second unoccupied setback time. Press either the up or down arrow tothe desired second unoccupied setback time

Commentaires sur ces manuels

Pas de commentaire